Features:
Maximum
temperature, lower temperatures were arbitrarily set.
Cooling
and heating mode can be choose.
Sensor
waterproof design, even line of skin damage due to leakage will not cause
electric shock.
Can
be used in fish tank, farming, agriculture, intelligent home, food,
industry, and so on.
Exquisite
appearance, but practicality.
Electrical
characteristics of product:
Temperature range:
temperature from minus 9 to 99
Resolution: temperature
0.1
Measurement accuracy:
0.1
Control precision: 1
Backlash accuracy: 1
Refresh rate: 0.5 second
Input voltage: AC110-240V
Measuring input :
NTC(10K0.5%) Waterproof type sensor
Output : relay 10A one
road
Environments requirement:
temperature from minus 10 to 60 , humidity from 20% to 85%
Product size:144mm(long)x99mm(wide)x44mm(high)
Power dissipation : static
current 40MA, attraction current 65MA
Instructions:
Start lights: The
equipment is Start to work when the red light on
Stop lights: The equipment is
stop working when the red light off
Digital tube:
The actual temperature were
display in the middle of red Digital tube
The setting temperature to
start were display on the left side of yellow Digital tube
The stop temperature of
setting were display on the right-hand side of yellow Digital tube
Button instruction:
Start "triangle":
set the temperature to start
Stop "triangle":
set the temperature to stop
Setting instruction:
; 1: Mode setting
Hold down the
Start "erected triangle" button and power on again,At this time the
digital tube displays-- E0.0 --,Press Stop "Inverted triangle"
to adjust the mode.
The pattern is as
follows:
E0.0 Temperature control mode ,
E0.1 Intermittent control mode
E0.2 Countdown
control mode , E0.3 Reservation control mode
;2: Calibration error
Hold down the Stop "Inverted
triangle" key when the power is off ,Then power on again,The thermostat
enters the calibration error state.The error value is shown in the middle of
the digital tube.It can be adjusted the numerical values by pressing the Start "triangle"
button,The maximum is 9, and the minimum is -9.
;3:E0.0 Temperature
control mode:
A:Refrigeration Mode:
The refrigeration
equipment will start to work if the setting temperature of start is greater
than stop and the testing temperature is greater than or equal to beginning.
The refrigeration
equipment will stop to work if the testing temperature less than or equal to
stop temperature,and it is changes back to its original state if the
temperature of testing is greater than beginning and is less than
stopping.
B:Heating Mode:
The Heating equipment will
start to work if the start temperature of set is less than stop and the
temperature of testing is small or equal to beginning.
If the testing temperature
greater than or equal to stop temperature ,the Heating equipment will
stop to work,W hen the temperature of testing is greater than beginning and is
less than stop, keep the original state relay.
C:When the temperature is more than 99 ,the digital tube will show HHHHHH .
When the
temperature is below minus 9 . The digital tube will show LLLLLL .
When sensor
without be detected, the digital tube will show EEEEEE .
;4:E0.1Intermittent time
control mode
The middle digital tube shows
"E0.1". Flashes once per second.
E0.1 The left-hand side
corresponds is stopping time:Press "triangle" keys (1 ~ 99 minutes)
to set up.
E0.1 The right-hand side
corresponds is opening time:Press "triangle" keys (1 ~ 99
minutes) to set up.
For example ,Set
"05" to the left of E0.1,The right setting"10"of "F1,It's
means stop for 5 minutes and turn on for 10 minutes.The red indicator goes out
when the engine is stopped,The red indicator light is on when the machine is boot,So
cycle.
;5: E0.2 Countdown time
control mode:
The middle digital tube shows
"E0.2". Set the range: 0001 ~ 9999 minutes,Flashes once per second.
E0.2 Left side corresponding
time:You can set it 1-99,Timing hour of time.
E0.2 Right side corresponding
time:You can set it 1-99,Timing minutes and seconds of time.
For example ,E0.2 The left
digital tube is set to "12",The right digital tube is set to
"00",The timing time is 1200 minutes,It means the timing time is 20
hours.
When arrive at the set time,
the plug will be turned off and the red light will go out.It is used for
regular shutdown, such as electric car charging, etc.
;6:E0.3"Appointment
time control mode
Intermediate digital tube
display "E0.3",The setting range is between 0001-9999 minutes.
E0.3 Left side corresponding
time:You can set it 1-99,Timing hour of time.
E0.3 Right side corresponding
time:You can set it 1-99,Timing minutes and seconds of time.
For example ,E0.3The left
digital tube is set to "12",The right digital tube is set to
"00",The timing time is 1200 minutes,It means the timing time is 20
hours.
When arrive at the set time,
The socket will open and the red light will be light,It can be applied to the
scheduled reservation boot.
Applications:
1.In the aspect of raise sets , the product is can be applied to fish
tank, aquarium and crawler box etc.
2.In terms of farming , the product is can be applied to incubation and
brood, temperature rise and keep , ventilation and heat dissipation,
temperature detection and warning etc.
3.In agriculture, the product is can be applied to strain culture
fermented, seedling culture , green house, cultivation and management of
flowers and edible fungi etc.
4.In the aspect of intelligent home , the product is can be applied to
floor heating, water heating , heater, electrothermal membrane ,
electrothermal bed , electric blanket and electric fan etc.
5.In terms of food , the product is can be applied to make wine , fermented
glutinous rice wine, flour fermentation , bean sprouts are cultivated ,
yogurt production , preservation of fruits and vegetables etc.
6.In industry , the product is can be applied to temperature control
cabinet , oven of experiment and warehouse monitor etc.
The operation panel and Wiring diagram:
Package Included:
1 x Digital LED Thermostat Temperature Controller
What's in the box
1 x Digital LED Thermostat Temperature Controller
